Ngày xuất bản: 30-11-2021
Số tạp chí: Số 3-2021

TS. Nguyễn Trọng Hà, TS.Phan Văn Phúc, ThS. Phan Văn Long

Từ khóa:

Ổn định phi tuyến
cột thép tiết diện thay đổi
ANSIS WORKBENCH
PTHH
mô hình 3D

Tóm tắt:

Bài báo trình bày kết quả nghiên cứu ứng xử của cột thép tiết diện thay đổi theo điều kiện ổn định phi tuyến bằng phương pháp phần tử hữu hạn (PTHH). Mô hình 3D của cột thép tiết diện thay đổi được xây dựng và phân tích bằng phần mềm ANSYS Workbench R18.1 với mô hình ổn định phi tuyến. Mô hình PTHH của cột tiết diện thay đổi sau đó được kiểm chứng với kết quả thí nghiệm trước đó cho thấy sự chính xác về sự làm việc và khả năng chịu lực của kết quả thí nghiệm. Từ mô hình này, nghiên cứu tiến hành khảo sát sự ảnh hưởng tỷ lệ độ dốc của cấu kiện, sự thay đổi bề rộng bản cánh đến sự ứng xử của cột tiết diện thay đổi theo điều kiện ổn định phi tuyến.

Nội dung:

Tài liệu tham khảo:

1.    N. Q. Viên (2007), "Báo cáo kết quả nghiên cứu đề tài khoa học cấp Bộ", Trường Đại học Xây dựng.

2.    S. P. Timoshenko and J. M. Gere (2009), Theory of elastic stability. Courier Corporation.

3.    G. Lee, M. Morrell and R. Ketter (1972), "Design of tapered members, WRC bulletin, no. 173", New York (NY): Welding Research Council.

4.    M. Crisinel and M. A. Hirt (2001), Charpentes métalliques: conception et dimensionnement des halles et bâtiments. Presses politechnique et universitaires romandes.

5.    L. Marques, A. Taras, L. S. da Silva, R. Greiner, and C. Rebelo (2012), "Development of a consistent buckling design procedure for tapered columns", Journal of Constructional Steel Research, vol. 72, pp. 61-74.

6.    A. Baptista and J. Muzeau (1998), "Design of tapered compression members according to Eurocode 3", Journal of Constructional Steel Research, vol. 46, pp. 146-148.

7.    I. G. Raftoyiannis and J. C. Ermopoulos (2005), "Stability of tapered and stepped steel columns with initial imperfections", Engineering Structures, vol. 27, no. 8, pp. 1248-1257.

8.    J. C. Naumes (2009), Biegeknicken und Biegedrillknicken von Stäben und Stabsystemen auf einheitlicher Grundlage. Shaker.

9.    Y. D. Kim (2010), "Behavior and design of metal building frames using general prismatic and web-tapered steel I-section members", Georgia Institute of Technology.

10.  L. Muir and C. J. Duncan (2011), "The AISC 2010 Specification and the 14th Edition Steel Construction Manual", in Structures Congress 2011, pp. 661-675.

11.  N. T. H. Đặng Xuân Hùng (2018), "Reliability assessment of buckling strength for tapered columns of steel portal frames with flexible joint of beam - column", Vietnam institute for building science and technology, pp. 292-298.

12.  T. Tankova, J. P. Martins, L. S. da Silva, R. Simões, and H. D. Craveiro (2018), "Experimental buckling behaviour of web tapered I-section steel columns", Journal of Constructional Steel Research, vol. 147, pp. 293-312.

13.  J. C. Ermopoulos (1986), "Buckling of tapered bars under stepped axial loads", Journal of structural engineering, vol. 112, no. 6, pp. 1346-1354.

14.  J. C. Ermopoulos (1997), "Equivalent buckling length of non-uniform members", Journal of Constructional Steel Research, vol. 42, no. 2, pp. 141-158.

15.  M. A. Hirt and M. Crisinel (2001), "Traité de Génie Civil Volume 11, Charpentes métalliques", ed: Presses Polytechniques et Universitaires Romandes.

Bài viết liên quan: